久操91 I 色妞精品av一区二区三区 I 一本色道久久综合亚洲精品按摩 I 未满十八18禁止免费网站 I 国产精品久久久久久在线观看 I 成人午夜视频在线播放 I 亚洲成人看片 I www.四虎在线 I 宅男噜噜噜66网站在线观看 I 巨乳在线播放 I 婷婷91 I 国产成人av网 I 日本又黄又硬又爽的大片 I 国产中文一区 I 伊人影院亚洲 I 国产成人精品午夜2022 I av边做边流奶水无码免费 I 欧美熟妇与小伙性欧美交 I 久久不见久久见www免费视频 I 亚洲国产中文曰韩丝袜 I 奇米视频888战线精品播放 I 欧美性猛交乱大交xxxxx I 久久综合色之久久综合 I 免费国产午夜高清在线视频 I 国产亚洲国际精品福利 I 国产黄色在线 I 欧美日韩国产图片区一区 I 亚洲国产成人精品女人久久久 I 成人无码h动漫在线网站免费 I 国产91美女视频

Chip capacitorIt is widely used in isolation, coupling, bypass, filtering, tuning loop, energy conversion, control circuit, and other aspects. Today we will teach you several methods to measure the quality of capacitors.

Most of the causes of damage to electrical products may be caused by capacitor damage. We have several methods to detect the quality of chip capacitors.

1. Check the quality of Electrolytic capacitor with diode gear of digital multimeter:

This method is suitable for Electrolytic capacitor breakdown. Set the digital multimeter at the diode position, and connect two probes to both ends of the Electrolytic capacitor. At this time, pay attention to whether the digital multimeter emits "drip drip" sound. If not, it is good and not broken down.

2. Capacitive resistance value testing method:

This method is suitable for detecting small capacitors below 10pF, and can only qualitatively check for leakage, internal short circuits, or breakdown phenomena. When measuring, a multimeter R can be used × 10k gear, use two probes to connect any two pins of the capacitor, and the resistance value should be infinite. If the measured resistance value (pointer swinging to the right) is zero, it indicates that the capacitor is damaged due to leakage or internal breakdown.

3. Direct capacitance testing method:
On some powerful digital multimeters, there is a capacitance test gear. When we set it to the capacitance test gear, the red lead is connected to the positive pole and the black lead is connected to the negative pole. If infinity occurs, it indicates that the capacitor is open or open circuit; When zero is detected, it indicates breakdown. A normal range number indicates normal operation.

4. Resonance method:

We observe the data through an LC resonant circuit. If there is an error in the data or the waveform is incorrect, it indicates that the capacitor has broken.

5. Check whether the Electrolytic capacitor is good or not with the resistance of pointer multimeter:

This method is applicable to capacitors with low withstand voltage value, such as Electrolytic capacitor with voltage below 6V or 10V.

Firstly, set the pointer multimeter to the resistance position, R * 1k position, and then connect the red lead to the negative electrode of the capacitor and the black lead to its positive electrode. Pay attention to the pointer changes of the multimeter while connecting.

The pointer will oscillate and then return to zero scale or near it after discharge. If a jump returns to zero, it proves that it is good, otherwise it is bad.
No matter what method we use, we use the basic principles of capacitors to monitor them. If we separate them from their basic properties to distinguish them, it would be wrong.